Nov
2026
20
Why Is Your Hot Tub Running but Not Heating?
A hot tub can continue circulating water even when its heating system is not working properly. The cause may be a restricted filter, inadequate flow, incorrect setting, faulty sensor, damaged heating element, or electrical problem. Before visiting a hot tub store for parts, check the controls, water level, and filter. If the problem continues, professional hot tub repair can identify the failed component.
At Seaway Pools & Hot Tubs, we provide professional hot tub repairs and hot tub service throughout Southern Ontario, for Beachcomber hot tubs and more. Our experts can help restore your hot tub, find replacement parts, and get your hot tub back into working order.
Here are some tips on how you can determine what's causing your hot tub trouble and how to get it working again.
Confirm the Temperature and Operating Mode
Begin with the simplest possibility. Confirm that the set temperature is higher than the current water temperature and that the spa is not operating in an economy, sleep, or vacation mode.
Some operating modes only allow the heater to run during scheduled filtration cycles. If someone recently changed the settings, the spa may appear to be malfunctioning even though it is following a different heating schedule.
Review the owner's manual before changing unfamiliar settings. If the control panel displays an error code, write it down rather than repeatedly clearing it. The code may help a technician identify whether the problem involves water flow, temperature sensors, overheating, or another system. For support with your error codes or hot tub troubleshooting, contact our local team of hot tub service experts at Seaway Pools & Hot Tubs.
Check the Water Level and Filter
Most hot tubs require consistent water flow before the heater can operate. If the water level is too low, the pump may draw in air and circulation may weaken.
Make sure the water reaches the level recommended by the manufacturer. Whether it's a Beachcomber hot tub, Viking hot tub, or another brand, the manufacturer recommendations may vary. Then inspect the filter. A filter loaded with oils, debris, or mineral deposits can restrict water movement enough to prevent the heater from turning on.
Turn off the power before removing the filter. Clean it according to the manufacturer's instructions or replace it if it is damaged or no longer responds to cleaning. Our hot tub supplies online or in-store includes replacement hot tub filters, water-care products, and other maintenance essentials.
Never operate the spa without a filter for regular use. A brief diagnostic step should only be performed when permitted by the manufacturer or recommended by a technician.
Look for Weak Circulation
Weak jets, fluctuating pressure, gurgling, or a flow-related error can indicate that the heater is not receiving enough water. Possible causes include:
- A clogged filter
- Low water
- An air lock after draining and refilling
- A closed or partially closed valve
- A blocked suction fitting
- A circulation-pump problem
- A faulty pressure or flow switch
If the problem started immediately after the tub was refilled, trapped air may be preventing the pump from moving water. Avoid allowing a pump to run dry, since this can damage seals and internal components.
Why Can the Pump Run While the Heater Does Not?
The pump and heater are separate components controlled by the spa's electrical and control systems. A circulation pump may continue operating even if the heating element, sensor, relay, or flow switch has failed.
A spa may also stop heating to protect itself when it detects insufficient flow or an unsafe temperature condition. This is why bypassing a sensor or safety device is not an appropriate repair.
Our FAQ on why a hot tub takes a long time to heat explains how weather, covers, water volume, and heater condition can also affect heating time.
Inspect the Cover and Surrounding Conditions
If the water is warming but cannot reach or maintain the set temperature, heat loss may be contributing to the problem. Check whether the cover closes evenly and whether it is waterlogged, damaged, or leaving gaps.
Cold weather, frequent use, strong wind, and repeatedly opening the cover can all increase heating time. However, a sudden loss of heating performance usually deserves a closer look, especially if the hot tub previously maintained its temperature under similar conditions.
When Should You Request Hot Tub Repair?
Arrange hot tub repair if:
- The heater does not activate despite adequate flow
- The water remains cold after the appropriate heating period
- A flow, sensor, or heating error keeps returning
- The breaker trips
- The equipment produces a burning smell
- The pump runs but circulation is weak
- The water overheats or the spa shuts itself down
Do not open control panels, test live electrical components, or replace a heater without the necessary training.
Trust the Hot Tub Service Experts at Seaway Pools & Hot Tubs
At Seaway Pools & Hot Tubs, our service team can inspect heating, circulation, pump, sensor, and control problems. Visit our hot tub store online or at our Markham and Newmarket showrooms for maintenance products, or submit a service request when troubleshooting does not restore normal heating.


